How to create the roof multifaceted: Difference between revisions

From HelpSystem
Jump to navigation Jump to search
(Created page with "{{Article table |commercial_product1=InstalSystem 5 |p2 =<!--gdy jest kolejny produkt handlowy, zamienić na->"produkt_handlowy2="--> |p3 =<!--...")
 
 
(2 intermediate revisions by the same user not shown)
Line 16: Line 16:
}}
}}
==Problem description==
==Problem description==
Problems associated with automatic generation of pipe feeds using the ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' tool are diagnosed by means of the following message:
* Multifaceted roof create using component ''<IS_TS id=AddRoofEdge/>''.
* '''''<IS_TS id=strErrNieUdaloSieUlozycPrzylaczy/>'''''.
* Icon of component is available in the ''2D Editor'' window on the ''<IS_TS id=NarzedziaGlowne/>'' bar in the ''<IS_TS id=lystrFloors/>'' section when the ''<IS_TS id=lystrFloors/>'' editing scope is enabled.<br/>[[File:TB-add-roof-edge-location.png|900 px|left|thumb|1. ''<IS_TS id=AddRoofEdge/>'']]<br clear="all"/>
The message informs that pipe feeds could not be generated automatically by means of the ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' tool, due to the following reasons:
* The program highlights in red edge of the roof, which is diagnosed impossible to present in ''<IS_TS id=View3D/>''.
* specified or automatically sized arrangement spacings are too large,
 
* manner of component crossing ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' is inappropriate (for the algorithm of automatic pipe feed arrangement),
* number of component crossings ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' is too large,
* ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' components are located too close to each other,
* width of the strip within which ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' generates pipe feeds is too small or too large (reaches beyond the borders of the heating zone).
==Solution==
==Solution==
* Specify smaller pipe feed arrangement spacing.
Use the ''AUTO'' and ''ORTO'' modes.
{{#ev:youtube|B0aVny2-vUw|900||||rel=0}}<br/>
{{#ev:youtube|us6xceXY_XA|900||||rel=0}}<br/>
* Change manner of ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' component arrangement.
 
{{#ev:youtube|pAcWrZ2mJR8|900||||rel=0}}<br/>
* Increase width of ''<IS_TS id=iNameOPStrefaPrzylaczy/>'' component arrangement area.
{{#ev:youtube|BXGQr_6KRwE|900||||rel=0}}<br/>
* Draw pipe feeds manually.
Depending on design circumstances, or when pipe feeds cannot be generated automatically, the tool for manual arrangement of pipe feeds can be used.<br/>{{Info}} [[Editing pipe feeds in a radiant system#Example of use|Manual pipe feeds editing]].
[[Category:TYPICAL PROBLEM]]
[[Category:TYPICAL PROBLEM]]
[[Category:InstalSystem 5]]
[[Category:InstalSystem 5]]

Latest revision as of 14:26, 3 November 2016

Product InstalSystem 5
Type of article TYPICAL PROBLEM
Source for translation IS 5.0 Beta 35


Problem description

  • Multifaceted roof create using component Add roof edge.
  • Icon of component is available in the 2D Editor window on the Main tools bar in the Construction section when the Construction editing scope is enabled.
    1. Add roof edge

  • The program highlights in red edge of the roof, which is diagnosed impossible to present in 3D view.

Solution

Use the AUTO and ORTO modes.


Retrieved from "https://en.test.help.instalsoft.com/index.php?title=How_to_create_the_roof_multifaceted&oldid=6624"